Product category:
Compliance Engineering
News Release from: Aeroflex
Edited by the Electronicstalk Editorial
Team on 06 April 2006
WiMAX tester to be previwed at June 2006
PlugFest
Aeroflex and Cetecom Spain have outlined the roadmap for the development and introduction of the WiMAX Forum's 802.16e protocol conformance test solution.
Following their recent contract win for development of the WiMAX Forum's 802.16e protocol conformance test solution, Aeroflex and Cetecom Spain have outlined the roadmap for the product's planned development and introduction Initial discussions with prospective technology partners are underway, all of whom will benefit from early access to the technology
This article was originally published on Electronicstalk on 19 Oct 2006 at 8.00am (UK)
Related stories
Development tests prove WiMAX compliance
A Development Test Mode for the WiMAX 802.16e protocol conformance test solution has been released by Aeroflex and AT4 wireless on behalf of the WiMAX Forum.
PXI-based platform heralds new wireless strategy
The Aeroflex 3000 series is a PXI-based modular test suite for mobile phone and general-purpose wireless test.
"Early customer involvement with the protocol conformance test solution is vital to its successful development and introduction within the timescales mandated by the WiMAX Forum", said Pete Nicholson, Business Unit Manager for Aeroflex Test Solutions, Wireless Division.
"Although initial discussions are already underway with several prospective technology partners, the opportunity to participate is still open to the broad spectrum of chipset developers, hardware manufacturers and test laboratories planning to focus on the WiMAX opportunity".
Intended to cut WiMAX device development costs through a defined certification process covering various levels of conformance complexity, the Aeroflex/Cetecom WiMAX 802.16e protocol conformance test solution (MINT 2230 series) will provide development, pre and full conformance testing of both subscriber and basestation equipment.
Further reading
Deeper analysis for broadband signals
Aeroflex has added a broad array of new signal measurement capabilities to its Celerity CS35000 Series broadband signal analyser and recorder family (BSA).
Radio tester takes on land mobile radio option
Aeroflex has licensed Trident Micro Systems' Passport protocol for use in its wireless communications test systems.
Software sppeds setup for microwave test systems
Aeroflex has integrated National Instruments' NI TestStand development system into its high-performance synthetic microwave test systems.
For chipset manufacturers this will include protocol stack development and for hardware manufacturers it will include integration and interoperability testing, enabling PHY and MAC layer conformance to be tested and validated prior to submission to a designated certification laboratory.
For certification laboratories it will provide a complete validation platform that supports ETSI developed TTCN3 test cases.
The roadmap calls for the introduction of the protocol conformance test solution in multiple phases that progressively increases the functionality available to provide both a basestation emulator (BSE - MINT 2230) for subscriber equipment testing and a subscriber station emulator (SSE - MINT 2231) for basestation equipment testing.
Each product provides a development test mode with air interface monitor and emulation (AIME) and test cases, conformance test mode with air interface monitor and emulation/conformance tester (AIME/CT) and validated test cases and supports multiple interface modes including Ethernet over cable, RF over cable and RF over air.
To coincide with the WiMAX Forum's PlugFest16e in June 2006 in Malaga, Aeroflex/Cetecom plan to introduce a pre-prototype development system that will enable initial protocol stack, digital signal processor and hardware testing.
Validation of the BSE protocol conformance test system will begin shortly thereafter with delivery of the BSE AIME product, followed by the BSE AIME/CT product, in Q4 CY2006.
Validation of the SSE protocol conformance test system will commence at the end of 2006 with delivery of the SSE AIME and SSE AIME/CT products beginning in Q2 2007.
"WiMAX is an important new technology development and to ensure its successful uptake it is essential that all developers have access to the right test tools when they need them", concluded Andres Moreno, Cetecom Wireless Division Director.
"By phasing the introduction of the MINT 2230 protocol conformance test solution and outlining the associated product introduction roadmap, developers will be able to plan accordingly".
"Those developers who want an early insight into the tools have the opportunity to apply to become one of our technology partners".
• Aeroflex: contact details and other news
• Email this article to a colleague
• Register for the free Electronicstalk email newsletter
• Electronicstalk Home Page
Search the Pro-Talk network of sites
