Product category:
Board-Level Instruments
News Release from: National Instruments | Subject: PXI-5661 and 5142
Edited by the Electronicstalk Editorial
Team on 31 August 2006
RF vector signal analyser runs on PXI
Three new products extend high-speed data acquisition and data streaming into RF and communications applications.
National Instruments has announced three new products that extend high-speed data acquisition and data streaming into RF and communications applications With the new RF vector signal analyser and two new IF digitisers that include advanced FPGA-based signal processing, engineers can continuously stream high-bandwidth RF data across high-speed buses, such as PCI and PXI, directly to a PC for processing and analysis
This article was originally published on Electronicstalk on 21 Mar 2001 at 8.00am (UK)
Related stories
High-precision audio and vibration measurements
For the first time on the PXI platform, engineers can make precision audio and vibration measurements with the National Instruments NI4472.
Modules condition a range of sensor signals
National Instruments has released new Signal Conditioning Component modules for frequency to voltage conversion, integrated circuit piezoelectric accelerometers and RTDs.
With PC processing and open software tools, engineers can create systems with unprecedented flexibility to address emerging standards or to prototype next-generation RF systems.
RF streaming is ideal for a variety of applications such as software-defined radio, record and playback of spectral communication signals and real-time spectral monitoring.
The National Instruments PXI-5661 2.7GHz RF vector signal analyser features 20MHz of real-time signal or modulation bandwidth, frequency-selective burst triggering and onboard signal processing for streaming data to a PC at full bandwidth.
Further reading
Low-cost data acquisition card runs from a laptop
National Instruments has released its lowest cost E Series data acquisition (DAQ) device for PCMCIA.
Toolset simplifies database connectivity
The LabVIEW Database Connectivity Toolset from National Instruments allows users to connect to local and remote databases from their LabVIEW applications without complex SQL programming.
More measurement options from real-time software
The newest version of LabVIEW Real-Time offers more measurement options and improves development time with superior performance and easy-to-use networking functions.
The new analyser implements an onboard quadrature digital downconvertor in an FPGA to significantly reduce the amount of data to transfer to the host PC so that high-bandwidth RF signals can directly transfer across the high-speed PXI backplane.
After the data is on the host PC, engineers can manipulate it in open software tools to make custom measurements, or even to emulate emerging communications standards as a software-defined radio.
The new module also includes a built-in burst trigger that engineers can use to trigger RF acquisitions based on a user-programmable power level and bandwidth.
NI 5142 communications digitisers are the IF components of the NI PXI-5661 analysers and are available separately in PXI or PCI for addressing a broad set of IF applications.
NI 5142 digitisers feature dual 14bit, 100Msample/s simultaneous-sampling channels with onboard signal processing.
Onboard processing features include a 40MHz programmable digital downconvertor and general-purpose alias-protected decimation, which tracks with the sample rate to protect sample data from higher-frequency aliases.
Engineers can combine the digital downconvertor with third-party RF-to-IF downconvertors for RF streaming applications.
"These new RF and IF products represent a shift in the way communications systems are designed and tested", said Tim Dehne, NI Senior Vice President of Engineering.
"By streaming RF or IF data across high-speed buses directly to a PC for processing, the challenge of developing a communications system now falls on software".
"Users can define their communications systems with open software, such as National Instruments LabView".
Using tools such as NI LabView graphical development software, engineers can use the new RF and IF hardware to perform user-defined measurement and analysis.
LabView tools, such as the Modulation and Spectral Measurements toolkits as well as the new MathScript node, offer a powerful platform for building next generation test systems or building a complete software-defined radio for designing emerging standards.
Engineers can also program the new hardware in many other programming environments such as National Instruments LabWindows/CVI for ANSI C development and Microsoft Visual Studio.
The new modules complement a variety of NI modular instruments including arbitrary waveform generators and digital waveform generator/analysers to build a complete custom mixed-signal application. Request a free brochure from National Instruments ...
• National Instruments: contact details and other news
• Email this article to a colleague
• Register for the free Electronicstalk email newsletter
• Electronicstalk Home Page
Search the Pro-Talk network of sites
